[转帖]backman维修常见问题

题号	维修常见问题
1	AN ERROR IN DAC INITIALIZATION HAS OCCURRED
2	AN TIMING ERROR IN DAC INITIALIZATION HAS OCCURRED
3	DAC INITIALIZATION ERROR
4	A DAC INITIALIZATION ERROR INDICATES THAT GLUCOSE ELECTRODE MUST BE RECHARGED
5	AN ERROR IN ADC SEQUENCE TIMING HASS OCCURRED
6	AN DAC TIMEOUT ERROR HAS OCCURRED
7	CALBRATION CANCELLED – A RUN TIME DIGNOSTIC ERROR WAS DETECTED
8	INSUFFICIENT REAGENT STRENGTH - BUN
9	INSUFFICIENT REAGENT STRENGTH - GLU
10	ERRATIC ADC
11	AN ROTATIONAL ERROR HAS OCURRED FOR THE SAMPLE CRANE
12	AN ERROR HAS OCCURRED IN RAISING THE SAMPLE CRANE
13	AN ERROR HAS OCCURRED IN LOWERRING THE SAMPLE CRANE
14	SAMPLE DETECTED IN THE UP POSITION
15	NO SAMPLE DETECTED
16	AN ERROR HAS OCCURRED ON PINCH VALVE “ E ”
17	AN ERROR HAS OCCURRED ON PINCH VALVE “ C ”
18	AN HOME ERROR HAS OCCURRED FOR THE RATIO PUMP.
19	AN ASPIRATE ERROR HAS OCCURRED FOR THE RATIO PUMP.
20	SAMPLE WHELL HOME ERROR
21	SAMPLE WHELL POSITION ERROR
22	CX3 / CX3* MDR BOARD
23	EXCESSIVE REFERENCE DRIFT
24	GLUCOSE GAIN ERROR
25	NOISE IN CREATININE ABSORBANCE INDICATES BUBBLES IN THE CUP CREA – URINE MODE LOW
26	CREATININE – URINE MODE TOO LOW
27	CAN NOT BOOT
28	MMC NOT READY TO RECEIVE
29	MMC CHECKSUM ERROR
30	A SOFTWARE QUEUE ERROR HAS OCCURRED
31	A DATABASE CROSS-CHECK HAS FAILED
32	A SERIOUS ERROR IN DISK OPEARATION HAS OCCURRED
33	FIRST SAMPLE LOW
34	CA/CREA LAMP IS DARK
35	CX3 CAL ERROR
36	RANGE ERROR： NA/K/CL/CO2，BUN/GLU/CA/CREA
37	BACK TO BACK – NA / K / CL / CO2
38	INJECTION CUP FLOODING
39	CALIBRATION FAILURE：OCR HIGH
40	校正FAILURE: OCR LOW
41	BAD PRECISION: CX3 / CX4
42	ISE DATA BAD PRECISION (离子资料不准确)
43	MOTION ERROR – SAMPLE PROBE UP/DOWN ERROR (样品针上下的错误)
43	MOTION ERROR – SAMPLE PROBE ROTATE (样品针轮换的错误)
44	MOTION ERROR – SAMPLE MIXER UP/DOWN (样品搅拌器上下的错误)
44	MOTION ERROR – SAMPLE MIXER ROTATE (样品搅拌器轮换的错误)
44	MOTION ERROR – SAMPLE MIXER SPIN (样品搅拌器旋转的错误)
45	MOTION ERROR – REAGENT PROBE UP/DOWN (试剂针上下的错误)
45	MOTION ERROR – REAGENT PROBE ROTATE (试剂针轮换的错误)
46	MOTION ERROR – REAGENT MIXER UP/DOWN (试剂搅拌器上下的错误)
46	MOTION ERROR – REAGENT MIXER ROTATE (试剂搅拌器轮换的错误)
46	MOTION ERROR – REAGENT MIXER SPIN (试剂搅拌器旋转的错误)
47	MOTION ERROR – REAGENT CAROUSEL
47	MOTION ERROR – SAMPLE CAROUSEL
48	MOTION ERROR – AUTOLOADER UP/DOWN
48	MOTION ERROR – AUTOLOADER SPIN
48	MOTION ERROR – WASH STATION
49	MOTION ERROR - SAMPLE PROBE WASH, SAMPLE PROBE AIR STRIP, REAGENT PROBE WASH, REAGENT PROBE AIR STRIP, WASH TO CUVETTE WASH, CUVETTE VACUUM, WASH MIX VALVE
50	MOTION ERROR - SUMP PUMP, SIP VALVE, VACUUM RESERVOIR DUMP, DI WATER MIXER VALVE, WASH TO ISE, DI WATER TO CUVETTE WASH
51	MOTION ERROR - MIX BOTTLE 1, MIX BOTTLE 2, SAMPLE PROBE WASH, SAMPLE PROBE AIR STRIP, REAGENT PROBE WASH, REAGENT PROBE AIR STRIP.
52	MOTION ERROR – REACTION CAROUSEL
53	MOTION ERROR – SAMPLE VALVE, SAMPLE PUMP, REAGENT VALVE, REAGENT PUMP
54	REAGENT DOOR IS OPEN
54	PROBE RINSE 没消耗
54	WASH BOTTLE 没充水
55	AUTOLOADER TIMEOUT
56	MOTION ERROR - BAD MESSAGE INTERRUPT ON MMC； UNDEFINED MSB ERROR；NO GOLDEN PHASE ON REAGENT；NO GOLDEN PHASE ON SAMPLE；NO GOLDEN PHASE ON REAGENT CAROUSEL；NO HOME ON REAGENT；NO HONE ON SAMPLE； NO HOME ON REAGENT CAROUSEL.
57	MOTION ERROR - ERROR IN MMC COMMUNICATION；BAD PACKET CHECKSUM；MAC PROCESSOR OR EPROM FAILURE； CHECKSUM ERROR IN MSC DOWNLOAD； BAD INIT HANDSHAKE WITH MSC.
58	MOTION SYSTEM IS BUSY: BAD ALIGNMENT DATA DETECHED
59	MOTION ERROR – CX3 PROBE NOT CLEAR
60	AIR PRESSURE OUT OF RANGE
61	WATER PRESSURE LOW/HIGH
62	LIQUID TRAP TOO HIGH
63	VACUUM BOTTLE FULL WATER
64	VACUUM PRESSURE LOW
65	SECONDARY PRESSURE LOW/HIGH
66	DI WATER LEVEL LOW
67	POWER SUPPLY FAILURE
68	PRINTER NO FUNCTION
69	CUVETTE FAILED WATER BLANK TEST
70	SECTOR CAN’T CLEAR
71	SECTOR NOT RUN
72	CABTRADGE CAN’T AUTOLOAD
73	WASTE BUCKET FULL
74	COMPRESSOR NO ACTION
75	BUBBLE GENERATOR NO BUBBLE
76	REAGENT PROBE LEAK
77	SAMPLE PROBE 滴水或悬水珠
78	WASH CUP 有水汽喷出
79	SAMPLE NOT DETECTED
80	REAGENT NOT DETECTED AT SAMPLE INJECTION
81	PELTIER FAILURE
82	PELTIER TEMPERATURE
83	CX3 POWER SUPPLY
84	ISE POWER SUPPLY FAILURE
85	DBM FATAL ERROR # 0, # 8, # ?
86	ANALOG CONTROL SENSOR ERROR
87	ANALOG COMMUNICATION ERROR
88	ANALOG COMMUNICATION ERROR
89	FATAL MMC ERROR
90	CHECKSUM ERROR STACK OVERFLOW HARDWARE MEMORY
91	MMC TIMEOUT ERROR
92	UNRECOGNIZED COMMAND SENT TO MMC
93	PHOTOMETER SYSTEM NOT READY
94	ANALOG WAS DEAD- AT INITIALIZATION
95	FATAL ERROR – IOM MODULE
96	FATAL ERROR - COULD NOT POST ALARM EVENT, ALARM REQUEST LIST FULL, COULD NOT OPEN ALARM REQUEST QUEUE, COULD NOT OPEN EVENT QUEUE; COULD NOT CREATE ALARM AQENT TASK; COULD NOT POST ALARM REQUEST; COULD NOT REPORT ALARM EVENT; ALARM NOT RUNNING.
97	SCSI PROBLEM
98	CAN’T START HEATER CALIBRTION CODE
99	DOES NOT MATCH DATA ON DISK
100	INCOMPATIBLE TEMPERATURE BOARDS
101	CANNOT START: FATAL ANALOG ERROR
102	CANNOT START: CX4 ANALOG SYSTEM NOT READY
103	CANNOT START: DATABASE ERROR
104	ERROR SYNCHRONIZING CX3 (ISE) PROBE AND CX4 SAMPLE CAROUSEL ASTAR

CX3与CX4维修常见问题与解决方法

问题与现象：	解决办法：	行动要求：
1． AN ERROR IN DAC INITIALIZATION -	CHECK: DETECTOR ELECTRODE REAGENT ANALOG BOARD HOME, RESET
2． AN TIMING ERROR IN DAC INITIALIZATION -	CHECK: ANALOG BOARD ADC BOARD RESET
3. DAC INITIALIZATION ERROR	CHECK: DETECTOR ELECTRODE REAGENT LEVEL- REAGENT CUP FILL/SIP/DRAIN FUNCTION REAGENT CUP 有无气泡 LAMP (CA/CREA) FLOW CELL 管路有无气泡 ANALOG BOARD
4. A DAC INITIALIZATION ERROR: INDICATES THAT THE GLUCOSE ELECTRODE MUST BE RECHARGED.	CHECK REAGENT WASH SOLUTION RATIO PUME E CAM & PROBE RECHARGE GLU ELECTRODE CHECK GEL
5. AN ERROR IN DAC SEQUENCE TIMING -	HOME RESET INSTRUMENT CHECK ADC BOARD
6. AN ADC TIMEOUT ERROR	HOME RESET CHECK ADC BOARD
7. CALIBRATION CANCELLED- A RUN TIME DIAGNOSTIC ERROR WAS DETECTED.	原因：BUN / GLU 强度不足 ADC BOARD 问题
8. INSUFFICIENT REAGENT STRENGTH – GLU LIMIT: >3200	CHECK REAGENT 开封日 WASH SOLUTION STIRRER （转动） GREEN / RED TUBE & PERI-PUMP FILL / SIP / DRAIN LINE C CAM & DRAIN PUMP ELETRODE & CONNECTOR RATIO PUMP E CAM & LINE “1” & “2”	一个月 水质不好或放置过久 CLEAN & MAINTENANCE REACTION CUP TUBE 两个月需更换一次 CLEAN ADJUST & REPLACE TUBE CLEAN 上层REFERENCE 应充满
9. INSUFFICIENT REAGENT STRENGTH – GLU LIMIT: < -3000	CHECK 如上 GEL是否过期 （水水的不要再用） REAGENT GLU ELECTRODE
10. ERRATIC ADC LIMIT: 15ADCS	FLOW CELL 有气泡 INJECTION CUP & SAMPLE PROBE SOLENOID VALVE & LINE “72” ELECTRODE EIC DRAIN SOLENOID VALVE & TUBE E CAM & WASH CHECK GROUNDING ANALOG 1 BOARD ADC BOARD	CLEAN INJECT 时有无密合 REPLACE
11. AN ROTATIONAL ERROR HAS OCCURRED FOR THE SAMPLE CRANE	有无异物挡住？ SAMPLE CRANE 是否在UP位置？ 是否在HOME位置？ INJECTION CUP 有无跳离位置？ +13V POWER 是否正常？ CRANE 无任何MOTION	HOME CHECK UP SENSOR UP/DOWN MOTOR CHECK HOME SENSOR CHECK POWER SUPPLY BOX 5 CHECK MDRI BOARD, 接头J 1204 MOTOR, 接头 J1505 & MMC BOARD
12. A ERROR HAS OCCURRED IN RAISING THE SAMPLE CRANE	按 HOME, SAMPLE CRANE 有无 UP UP时不顺畅 POWER 是否正常？	CHECK UP HOME SENSOR CHECK MOTOR 之皮带及轴承 CHECK MOTOR, J1501接头 MDRI BOARD, J1203 接头 MMC BOARD
13. AN ERROR HAS OCCURRED IN LOWERING THE SAMPLE CRANE	按HOME, SAMPLE CRANE 有无UP SAMPLE CRANE 无任何动作	CHECK UP/DOWN MOTOR & 皮带 CHECK UP (HOME) SENSOR MD1 BOARD, J1203 接头
14. SAMPLE DETECTED IN THE UP POSITION	SAMPLE PROBE 接头有无湿 MD2 BOARD – DS4 & DS5 是否同时亮？	DRY CHECK HARNESS MD2 BOARD, P1308接头
15. NO SAMPLE DETECTED	SAMPLE 吸检体，MD2 BOARD 之DS4应亮 DS4有亮，DS5没亮 （是一个ENABLE的动作，亮起来表示已进入ROTETOR状况）	REPLACE MD2 BOARD CHECK HARNESS 由无断线 P1308接头有无脱落 MD2 BOARD,MMC BOARD
16. AN ERROR HAS OCCURRED ON PINCH VALVE “E”	按HOME, 看PINCH VALVE有无动作 HOME 位置在 ”3”
17. AN ERROR HAS OCCURRED ON PINCH VALVE “C”	按HOME, 看PINCH VALVE有无动作 HOME 位置在”1”	CHECK MOTOR & HARNESS, J1505接头 MDRI BOARD, P1207接头 +13V POWER SUPPLY MMC BOARD CHECK SENSOR
18. AN HOME ERROR HAS OCCURRED FOR THE RATIO PUMP	RATIO PUMP 是否在HOME位置？ E CAM 是否在正常位置？ （HOME位置在“3”） RATIO PUMP UP时不顺	CHECK MOTOR & HARNESS, J1502接头 MDI BOARD, P1205接头 +13V POWER SUPPLY MMC BOARD LOOK E CAM EVENT LUBRICATION PATIO PUMP 上之螺丝锁太紧
19. AN ASPIRATE ERROR HAS OCCURRED FOR THE RATIO PUMP	发生於RATIO PUMP DOWN 时 HOME SENSOR 为ON	CHECK MOTOR, HARNESS +13V POWER HOME SENSOR
20. SAMPLE WHEEL HOME ERROR	HOME TURNTABLE 有无空转？	CHECK 13V POWER SUPPLY MDR 2 BOARD, 接头P1306 HARNESS CHECK HOME SENSOR HARNESS
21. SAMPLE WHEEL POSITION ERROR	SENSOR DETECTED 有问题 （清SAMPLE WHEEL下方之(6)颗SENSOR 或 RE-BOOTING)	CHECK SENSOR, FLAG
22. CX3/CX3* MDR 1 & 2 BOARD LED判读 CX3 MDR 1 DSI: PERI-PUMP ON DS2: STEPMOTOR ACTION MDR2: DS1: DS2: SAMPLE TURNTABLE – STEP SINGAL DS3: MODULE FILL/DRAIN MOTOR & STIRRER, REFERENCE MOTOR – ON SIGNAL DS4: SAMPLE SENSE DS5: SAMPLE DETECTER	CX3* DS2/3/4/5: E CAM DS6/7/8/9: C CAM DS10/11/12/13: SAMPLE CRANE VERTICAL DS14/15/16/17: SAMPLE CRANE ROTATICAL DS18/19/20/21: RATIO PUMP DS22: RATIO PUMP IS HOME DS23: CRANE ROTATION DETECTED DS24: CRANE ROTATION HOME DS25: CRANE VERTICAL HOME DS26: DS27: C CAM HOME DS28: E CAM HOME
23. EXCESSIVE REFERENCE DRIFT LIMITS: NA - 400 ADCS X – 200 ADCS CL – 200 ADCS CO2 – -20% ~ +30%	CHECK DAMPER CHECK ELETRODE 有无锁紧 PINCH VALUE (在FLOW CELL底下)动作是否正常，TUBE是否挟紧或过短 CHECK FLOW CELL 有无气泡 CHECK REFERENCE ADC 值是否全部下降且PRIME后上升- 单独时- CHECK RATIO PUMP 有无气泡 INJECTION CUP 是否在定位？ CHECK AMBIENT TEMPERATURE (CO2) WASH SOLUTION	REPLACE NA REFERENCE ELECTRODE CHECK 个别ELECTRODE
24. GLUCOSE GAIN ERROR	HOME CHECK REACTION CUP & 吸检体有无问题 CHECK ELECTRODE CHECK ANALOG 2 BOARD ADC BOARD REBOOT INSTRUMENT	CHECK REAGENT RECHARGE GLU ELECTRODE 3D,4E,8255 (IC NUMBER)
25. NOISE IN CREATININE ABSORBANCE INDICATES BUBLES IN THE CUP	CHECK REACTION CUP 内有无气泡 LAMP & DETECTOR	CLEAN STIRRER & STIRRER MOTOR REACTION CUP CHECK PERI-PUMP & TUBE FILL LINE
26. CREATININE – URINE MODE TOO LOW (URINE MODE 是机器自行换算)	CHECK 校正液 & REAGENT CHECK ADC NUMBER – IA 是否比以前大 CHECK LAMP & SUPPLY VOLTAGE	CLEAN REACTION CUP & STIRRER LAMP & DETECTOR ANALOG 2 BOARD ADC BOARD U22,19
27. CAN NOT BOOT	CHECK CPU BOARD “ SEVEN SEGMENT” LED DISPLAY “ 0 ” “ 1 “ “ 2 “ “ 3 “ “ 4 “ “ 5 “ “ 6 “ “ 7 “ “ 8 “ “ 9 “ “ A “ “ B “ “ C “ “ D “ “ E “ “ F “	CHECK: 1/0 SERIAL & TERMINAL RAM BOARD ISBX BOARD & PRINTER COMM BOARD – USARTS COMM BOARD – PIC CPU BOARD – ROM CPU BOARD – U45 & U46 COMM BOARD – U21 CPU BOARD – U20 CPU BOARD – FAIL SAFE CPU BOARD – WATCHDOG ISBX BOARD & PRINTER CPU BOARD – U5 RAM BOARD DISK CONTROLLER LOAD OPERATING SOFTWARE

28. MMC NOT READY TO RECEIVE	CHECK MMC BOARD REBOOT
29. MMC CHECKSUM ERROR	CHECK MMC BOARD REBOOT
30. A SOFTWARE QUEUE ERROR HAS OCCURRED	CHECK CPU/RAM BOARD REBOOT
31. A DATABASE CROSS-CHECK HAS FAILED	CHECK CPU/RAM BOARD REBOOT
32. A SERIOUS ERROR IN DISK OPERATION HAS OCCURRED	ERROR NUMBER = 651 652 650	WRITE-PROTECTED TAB IS LOCK DISKETTE 未插入 REPLACE DISKETTE DISK DRIVER DISK CONTROLLER BOARD +12V, +5V POWER SUPPLY
33. FIRST SAMPLE LOW (CA/CREA/BUN/CREA)	TEMPERATURE CONTROL BOARD – LED 有无一闪一闪？ CHECK SIP LINE DRAIN LINE FILL PERI-PUMP 之TUBE SAMPLE PROBE 是否滴水？ STIRRER RATIO PUMP 有无气泡？ REAGENT LINE	CHECK E CAM “1” “2” TUBE
34. CA/CREA LAMP IS DARK	CHECK POWER SUPPLY BOX 3 ANALOG 3 BOARD LAMP FUSE
35. CX3 CAL ERROR: 多数校正不过时 ONLY ELECTRODE ONLY CHEMISTRY	CHECK STANDARD, REFERENCE SOLUTION SAMPLE PROBE & LINE “1”, “2” 有无充满 REFERENCE WASH SOLUTION PROBLEM SAMPLE PROBE DROPING E CAM RATIO PUMP – 有无气泡存在？ （THE TOP OF RATIO PUMP） ADC VALUE 相同- CHECK CONNECTOR & ADC BOARD FLOW CELL / INJECTION CUP 脏或阻塞 CHECK SOLENOID VALVE 动作 （FLOW CELL 下方 & INJECTION CUP 旁） RATIO PUMP – CYLINDER 4 & 5 CHECK NA ELECTRODE CHECK REFERENCE SOLUTION 吸检体 – SAMPLE PROBE & E CAM C CAM PERI- PUMP & TUBE
36. RANGE ERROR: NA/K/CL/CO2 CAL 1 CAL 2 BUN/GLU/CA/CREA CAL 1 BUN/GLU/CA/CREA CAL 2	• REFERENCE 是否接近负下限？ • CHECK REFERENCE ELECTRODE 或每一个 ELECTRODE • CHECK CO2 MEMBRANE 有无破裂？电极头 前有无气泡？ • CHECK RATIO PUMP, E CAM & TUBE REAGENT – BUFFER, ACID • CHECK INJECTION CUP / FLOW CELL SOLENOID VALVE & TUBE • CHECK STANDARD • CO2 ALKALINE BUFFER 使用是否超过一个 月？ • ELECTRODE 头有无气泡？ K CAL 2 FAIL 且接近下限 • CL ELECTRODE 是否MAINTENANCE CHECK STANDARD CHECK STIRRER 转动 CHECK TEMPERATURE CHECK REATION CUP DRAIN/SIP/FILL有无问题 REAGENT CONDITION 不好 OR REPLACE GREEN/RED TUBING (PERI-PUMP) RECHARGE GLU ELECTRODE OR MEMBRANE破 BUN ELECTRODE 是否脏了？ CHECK LAMP & DETECTOR 吸检体有问题 REACTION CUP – DRAIN/SIP/FILL有问题 污染 – INJECTION CUP & SAMPLE PROBE 洗不干净 GLU ELECTRODE 是否要重新CHARGE?	REPLACE REFERENCE REPLACE NA/CO2 REPLACE K TIP REPLACE CL ELECTRODE C CAM, PERI –PUMP & TUBE CHECK E CAM & SAMPLE PROBE
37. BACK TO BACK – NA/K/CL/CO2 GLU/BUN CA / CREA	REFERENCE IR值是否上下变动？ SAMPLE 变动？ STIRRER 是否转动正常？ REACTION CUP 有无气泡？ CHECK DRAIN/FILL/SIP动作是否正常? CHECK INJECTION CUP & SAMPLE PROBE 外表有无悬水珠 SAMPLE VOLUME 是否正常？ INJECTION CUP 有无满出？ CHECK DRAIN/SIP/FILL 动作	CHECK FLOW CELL 是否干净？ SAMPLE PROBE 有无阻塞？ PINCH VALUE “E” 及 LINE “2” & “1” DAMPER 是否满？ PINCH VALUE 是否开启正常？ CHECK SAMPLE PROBE RATIO PUMP & E CAM WASH 有无动作？ CHECK MOTOR CLEAN FILL LINE & REACTION CUP 检查管路与STIRRER有无松动 REPLACE TUBE CHECK PINCH VALUE “C” CHECK SAMPLE PROBE, RATIO PUMP, E CAM LINE “73” 有无塞住，SILICONE TUBE批乏，DRAIN PUMP 无动作 CHECK TUBE
38. INJECTION CUP FLOODING (淹水)	CHECK DRAIN LINE, SOLENOID VALVE FLOW CELL – SOLENOID VALVE, LINE INJECTION CUP 有无卡住？
39. CALIBRATION FAILURE: OCR HI CX3部分 CHEMISTRY ELECTRODE CX4 部分	前一项 OCR LOW REACTION LEVEL LOW TEMPERATURE TOO HIGH ANALOG BOARD INJECTION CUP DRAIN 不良 CHECK WASH CUP – NO WASH & AIR STRIP REAGENT PROBE / MIXER SAMPLE PROBE / MIXER CUVETTE WASH STATION CARRYOVER	CHECK REACTION CUP LEVEL CHECK NA ELECTRODE RATIO PUMP WASH SOLUTION
40. 校正FAILURE: OCR LOW CX3部分 CHEMISTRY ELECTRODE CX4部分	LAMP 熄 (CA/CREA) CHECK STANDARD ELECTRODE SENSITIVITY SOLENOID VALVE & TUBE INJECTION CUP FLOW CELL SAMPLE PROBE RATIO PUMP & E CAM 校正液放错位置 CHECK SAMPLE PROBE PUMP & SYRINGE SAMPLE MIXER CUVETTE 脏或淹水 REAGENT 期限，CARTRIDGE 有无泡	CHECK POWER SUPPLY RATIO PUMP SAMPLE PROBE E CAM “1” “2” TUBE STANDARD ELECTRODE / DETECTOR/ SENSITIVITY REAGENT & FILL LINE REACTION CUP STIRRER C CAM, DRAIN/SIP LINE & DRAIN PERI-PUMP/TUBE
41. BAD PRECISION: CX3部分 BUN, GLU CA, CREA NA/K/CL/CO2 CX4部分	CHECK ELECTRODE STIRRER REATION CUP TEMPERATURE FILL, PERI-PUMP TUBE & LINE SIP/DRAIN LINE C CAM & DRAIN PERI-PUMP “1” & “2” SAMPLE PROBE, INJECTION CUP CHECK DETECTOR LAMP & LAMP VOLTAGE STIRRER REATION CUP TEMPERATURE FILL PERI-PUMP TUBE & LINE SIP / DRAIN LINE C CAM & DRAIN PERI-PUMP GRAY TUBE E CAM & RATIO PUMP “1” & “2” TUBE SAMPLE PROBE & INJECTION CUP CHECK SAMPLE PROBE E CAM REFERENCE LINE & PUMP SOLENOID VALVE & SILICONE TUBE ALKALINE BEFFER LINE ELECTRODE & MEMBRANE FLOW CELL & DAMPER CLEAN CHECK SAMPLE / REAGENT MIXER SAMPLE / REAGENT PROBE SAMPLE / REAGENT SYRINGE (SAMPLE SYRINGE建议每两周换一次) CUVETTE (用超音波洗最好) WASH STATION & WIPPER WASH CUP REAGENT CONDITION REAGENT CAROUSEL TEMPERATURE LAMP FLASH TIMING HYDRO SYSTEM CONDITION
42. ISE DATA BAD PRECISION	NA/K/CL/CO2有共同性 SINGLE FLOW CELL 最前最后项目 CO2	REFERENCE ELECTRODE (NA/CO2) PERI-PUMP (REFERENCE SOLUTION, ALKALINE BUFFER) E CAM & INJECTION CUP CHECK ELECTRODE FLOW CELL 内有气泡 SOLENOID VALVE “72” TUBE SAMPLE PROBE SOLENOID VALVE, TUBE DAMPER
43. MOTION ERROR: SAMPLE PROBE UP/DOWN ERROR SAMPLE PROBE ROTATE	CHECK PROBE定位 MOTOR & CONNECTOR HARNESS BELT SAMPLE CAROUSEL 位置 MSC 2 BOARD CHECK PROBE定位及是否UP位置？ MOTOR HOME SENSOR MSC 2 BOARD	ALIGNMENT SAMPLE MIXER VERTICAL & HEIGHT ALIGNMENT SAMPLE CAROUSEL ALIGNMENT SAMPLE PROBE

44. MOTION ERROR:

SAMPLE MIXER UP/DOWN CHECK MIXER 定位--- ALIGNMENT SAMPLE MIXER VERTICAL & HEIGHT

MOTOR & CONNECTOR

HOME SENSOR

BELT

MSC 2 BOARD

SAMPLE MIXER ROTATE CHECK MIXER 定位及是否UP位置--- ALIGNMENT SAMPLE MIXER ROTATION

MOTOR & HARNESS CONNECTOR

SENSOR

MSC 2 BOARD

SAMPLE MIXER SPIN CHECK SPEED CONTROLLER BOARD

MOTOR & CONNECTOR

BEARING

MSC 2 BOARD

45.MOTION ERROR—

REAGENT PROBE UP/DOWN CHECK PROBE 定位--- ALIGNMENT REAGENT PROBE VERTICAL HEIGHT

MOTOR (P898头)

SENSOR (P896头)

BELT

REAGENT CARTRIDGE--- 有无气泡

MSC 3 BOARD

REAGENT PROBE ROTATE CHECK PROBE定位及是否UP位置--- ALIGNMENT REAGENT PROBE ROTATION

MOTOR (P873头)

HOME SENSOR

MSC 3 BOARD

46.MOTION ERROR:

REAGENT MIXER ROTATE CHECK MIXER 定位及是否UP位置--- ALIGNMENT REAGENT MIXER

MOTOR

HOME SENSOR

MSC 3 BOARD

REAGENT MIXER UP/DOWN CHECK MIXER 定位--- ALIGNMENT REAGENT MIXER VERTICAL & VERTICAL

MOTOR

BELT

UP HOME SENSOR

REACTION CAROUSEL 位置

MSC 3 BOARD

REAGENT MIXER SPIN CHECK SPEED CONTROLLER BOARD

MOTOR, BEARING & CONNECTOR

MSC 3 BOARD

47. MOTION ERROR:

REAGENT CAROUSEL CHECK CAROUSEL 有无松动--- ALIGNMENT

有无CARTRIDGE 未推入位置

HOME SENSOR

POSITION SENSOR

BELT

MOTOR

HARNESS & CONNECTOR

MSC 1 BOARD

SAMPLE CAROUSEL CHECK 有无异物--- ALIGNMENT

MOTOR, HARNESS, CONNECTOR

POSITION SENSOR

MSC 5 BOARD

48.MOTION ERROR:

AUTOLOADER UP/DOWN ERROR CHECK PRIME PRESSURE

MSC 5 BOARD

MAC VALVE

15PSI REGULATOR & RELIEF VALVE

相关的 HARNESS

UP/DOWN SENSOR

AUTOLOADER SPIN CHECK AUTOLOADER ASSEMBLY

MOTOR

FLAG & SENSOR

MSC 5 BOARD

WASH STATION CHECK MOTOR & CABDE

SENSOR--- ADJUST (ENTER DIAGNOSTICS)

REACTION CAROUSEL 之 CUVETTE 位置--- ALIGNMENT REACTION CAROUSEL

MOTOR 之导螺杆---有无动并润滑之

49. MOTION ERROR:

SAMPLE PROBE WASH CHECK 8L SOLENOID VALVE & CABLE

CHECK MSC 4 BOARD

SAMPLE PROBE AIR STRIP CHECK 4A SOLENOID VALVE & CABLE

CHECK MSC 4 BOARD

REAGENT PROBE WASH CHECK 7L SOLENOID VALVE & CABLE

CHECK MSC 4 BOARD

REAGENT PROBE AIR STRIP CHECK 5A SOLENOID VALVE & CABLE

CHECK MSC 4 BOARD

WASH TO CUVETTE WASH CHECK 9L SOLENOID VALVE & CABLE

CHECK MSC 5 BOARD

CUVETTE VACUUM CHECK 10V SOLENOID VALVE & CABLE

CHECK MSC 5 BOARD

WASH MIX VALVE CHECK 4L SOLENOID VALVE & CABLE

CHECK MSC BOARD

50.MOTION ERROR:

SUMP PUMP CHECK 5L SOLENOID VALVE & CABLE

CHECK MSC 2 BOARD

SIP VALVE CHECK 11V SOLENOID VALVE & CABLE

CHECK MSC 2 BOARD

VACUUM RESERVOIR DUMP CHECK 5L SOLENOID VALVE & CABLE

CHECK MSC 5 BOARD

DI WATER MIXER VALVE CHECK 3L SOLENOID VALVE & CABLE

CHECK MSC 4 BOARD

WASH TO ISE CHECK 6L SOLENOID VALVE & CABLE

CHECK MSC 4 BOARD

DI WATER TO CUVETTE WASH CHECK 2L SOLENOID VALVE & CABLE

CHECK MSC 5 BOARD

51. MOTION ERROR:

MIX BOTTLE 1 CHECK 1A SOLENOID VALVE & CABLE

MSC 1 BOARD

MIX BOTTLE 2 CHECK 2A SOLENOID VALVE & CABLE

MSC 2 BOARD

SAMPLE PROBE WASH CHECK 8L SOLENOID VALVE & CABLE

MSC 4 BOARD

SAMPLE PROBE AIR STRIP CHECK 4A SOLENOID VALVE & CABLE

MSC 4 BOARD

REAGENT PROBE WASH CHECK 7L SOLENOID VALVE & CABLE

MSC 4 BOARD

REAGENT PROBE AIR STRIP CHECK 5A SOLENOID VALVE & CABLE

MSC 4 BOARD

52. MOTION ERROR:

REACTION CAROUSEL CHECK MOTOR & CABLE

CHECK 有无异物---注意WASH CUP 之出气FILTER(在HYDRO 上方)

CHECK PROXIMITY SENSOR---ENTER DIAGNOSTIC RUN SENSOR ALIGNMENT

CHECK MSC 1 BOARD

ENTER DIAGNOTIC SYSTEM ( EXTENDED MODE )

--- RUN 7. REACTION CAROUSEL SYSTEM

1. REACTION CAROUSEL

3. STEPPER/SENSOR

1. HOMING TEST

2. START-UP RELIABILITY TEST

3. CORRELATION TEST

53. MOTION ERROR:

SAMPLE VALVE CHECK MSC 4 BOARD

VALVE MOTOR---J838 接头

VALVE SENSOR--- J840 接头

VALVE SENSOR DISC

CABLE BETWEEN MSC 4 BOARD AND PUMP INTERFACE BOARD

SAMPLE PUMP LUBRICATION UP/DOWN

CHECK MOTOR, 接头J842,CABLE

FLAG DISC , HOME SENSOR

SAMPLE VALVE

SAMPLE SYRINGE & PROBE

REAGENT VALVE CHECK MSC 4 BOARD

VALVE MOTOR-- J837 接头

VALVE SENSOR-- J839 接头

VALVE SENSOR DISC

CABLE BETWEEN MSC 4 BOARD AND PUMP INTERFACE BOARD

REAGENT PUMP LUBRICATION UP/DOWN

CHECK MOTOR, 接头J837,CABLE

REAGENT VALVE

REAGENT SYRINGE & PROBE

54.MOTOR ERROR:

REAGENT DOOR IS OPEN CHECK SENSOR---ADJUST SENSOR POSITION

CHECK CABLE

CHECK INTERFACE BOARD

PROBE RINSE 没消耗 INLINE FILTER

CHECK BUBBLE CENERATOR--- SOLENOID VALVE (25PSI & RINSE ) 有无动作

CHECK 10PSI PRESSURE--- WATER PRESSURE REGULATOR, RELIFE VALVE

FASH BOTTLE 没有水 CHECK SOLENOID VALVE (3L & 4L )

CHECK SOLENOID VALVE (1A, 2A )

55. AUTOLOADER TIMEOUT CHECK 25PSI PRESSURE

15PSI REGULATOR, RELIFE VALVE

AUTOLOADER SOLENOID VALVE

AUTOLOADER 有无漏气

UP/DOWN SENSOR

MSC VALVE (PTS)

INLINE FILTER (PTS )

ENTER DIAGNOSTIC---ADJUST UP/DOWN TIMING (PTS)

56. MOTION ERROR:

BAD MESSAGE INTERRUPT ON MMC CHECK MMC BOARD

UNDEFINED MSB ERROR CHECK MSC BOARD

NO GOLDEN PHASE ON REAGENT CHECK MSC 2 BOARD

NO GOLDEN PHASE ON SAMPLE CHECK MSC 3 BOARD

NO GOLDEN PHASE ON REAGENT CAROUSEL CHECK MSC 1 BOARD

NO HOME ON REAGENT CHECK REAGENT

NO HONE ON SAMPLE

NO HOME ON REAGENT CAROUSEL

57.MOTION ERROR:

ERROR IN MMC COMMUNICATION CHECK MMC BOARD--- REBOOT

REPLACE MMC BOARD

BAD PACKET CHECKSUM CHECK MMC BOARD--- REBOOT

MAC PROCESSOR OR EPROM FAILURE CHECK MSC BOARD--- CR24, CR25 是否亮，REPLACE MSC BOARD

REBOOT

CHECKSUM ERROR IN MSC DOWNLOAD CHECK POWER SUPPLY 3

MMC/ MSC BOARD--- REBOOT

BAD INIT HANDSHAKE WITH MSC CHECK MSC BOARD--- ROBOOT

58. MOTION SYSTEM IS BUSY IDLE SYSTEM THAN REBOOT

BAD ALIGNMENT DATA DETECTED RESTORE BACKUP DISKETTE

REBOOT

59. MOTION ERROR:

CX3 PROBE NOT CLEAR HOME

CHECK SAMPLE CRANE

+13V POWER SUPPLY

MDR 1 BOARD

MMC BOARD

60.AIR PRESSURE OUT OF RANGE STANDBY 25PSI REGULATOR 是否已调到底--- CHECK有无漏气

RUNNING 时，气体建立是否快--- CHECK INLINE FILTER

PUMP A3-A4 TUBE

PILOT OPERATOR SWITCH

水压有无上下漂移---CHECK RELIFE VALVE

CHECK SENSOR

CHECK COMPRESSOR--- REPLACE REBUILT KIT

61. WATER PRESSURE LOW OR HIGHT CHECK 25PSI PRESSURE

CHECK REGULATOR, RELIFE VALVE

CHECK有无漏气

CHECK WASH BOTTLE & 1A, 2A VALVE

CHECK SENSOR

62. LIQUID TRAP TOO HIGH CHECK PRIME PRESSURE--- 见 25PSI PRESSURE LOW

3 WAY VALVE (5L) 有无动作, 25PSI AIR进入把WASTE赶入WASTE BOTTLE---REPLACE

CHECK MSC 5 BOARD--- CONTROL 5A VALVE

SENSOR

RESERVOIR --- CLEAN

63. VACUUM BOTTLE FULL WATER CHECK 3 WAY VALVE (5L)

CHECK 1L, 6L VALVE 与其连接之 CHECK VALVE

CHECK PILOTOPERATOR SWITH 动作

LIQUID TRAP 或有积水

64. VACUUM PRESSURE LOW 有无漏气

TANK有无锁紧

CHECK 5L, 10V, 1L CHECK VALVE

6L CHECK VALVE

出气 FILTER有无漏气

CHECK SENSOR

65. SECONDARY PRESSURE HOME

LOW OR HIGH CHECK 3A VALVE

CHECK REGULATOR P/N 759858

CHECK WASH CONCENTRATE 2 BOTTLE

CHECK SENSOR

66. DI WATER LEVEL LOW CHECK 水系统 （进水压力要大于30PSI ）

CHECK WATER PRESSURE--- REGULATER & RELIFE VALVE

CHECK SENSOR 及接头 (J985 & J984 )

MPT VALVE是否关住（进水关闭）

进水VALVE, 接头 P818--- MSC 3 BOARD

67. POWER SUPPLY FAILURE CHECK STATUS BOARD

CHECK INDICATOR BOARD

POWER SUPPLY

POWER SUPPLY1 V1: +5V LOGIC, DISK DRIVER

V2: +24V HEATERS, LAMP SUPPLY

V3: +12V LOGIC, DISK DRIVER, COMMUNICATION

V4: -12V COMMUNICATION

POWER SUPPLY2 V2: +24V REFRIGERATOR

V3: +15V ANALOG

V4: -15V ANALOG

POWER SUPPLY3 V1: +5V MOTOR LOGIC

V3: +38V MOTORS

V4: +12V SOLENOID VALVE

68. PRINTER NO FUNCTION CHECK PRINTER CABLE

RESET PRINTER

RESTART PRINTER

CHECK ISBX PRINTER INTERFACER BOARD (ONCPU BOARD)

RESET INSTRUMENT

69. CUVETTE FAILED WATER BLANK TEST CUVETTE---CLEAN

CUVETTE---CHECK WASH STATION

ALIGNMENT WASH STATION

CHECK REACTION CAROUSEL 定位

CUVETTE有无淹水--- CHECK WATER PRESSURE & 7L, 8L VALVE

VACUUM PRESSURE (5L VALVE)

VACUUM/WASH PROBE

CHECK VALVE

LAMP 有无 FLASH---CHECK REACTION WHEEL

LAMP POWER SUPPLY

MAC BOARD

SYNC PROXIMITY SENSOR

70. SECTOR CAN’T CLEAR REBOOT

71. SECTOR 不RUN SECTOR LABEL, 有问题

CHECK HYDRO, SYSTEM 左上方SECTOR READER BOARD之二个LED在READ SECTOR有无一闪一闪

---一为DATA TRACK

二为 TIMING TRACK

72. CABTRIDGE CAN’T AUTOLOAD LABEL有问题

CHECK BARCODE READER

CHECK INTERFACE BOARD

73. WASTE BUCKET FULL DRAIN PUMP 是否工作正常---REPLACE DRAIN PUMP OR CLEAN

CHECK SSR & CABLE

WASH BOTTLE 1 & 2 有无气泡---REPLACE 其上方CHECK VALVE

CHECK FLOAT SWITCH (WASTER BOTTLES内 )有无动作不良，因此造成

CHECK FLOAT SWITCH (WASH BOTTLE 1 & 2 内)动作是否正常

74. COMPRESSOR没动作 CHECK K1 SSR

STATUS BOARD

AC/ DC CONTROL BOARD (在PS8下方)

MOTOR & CABLE

75. BUBBLE GENERATOR无气泡产生:

OLD TYPE 针阀有无动作--- CHECK接头 J928

POWER +12V POWER SUPPLY

SOLENOID VALVE (25 PSI PRESSURE, RIGHT)

---PRIME PRESSURE

---CHECK PROBE RINSE 限制器 & FILTER

CHECK RINSE SOLENOID VALVE (LEFT), WATER PRESSURE

ADJUST 10 PSI REGULATOR

CHECK BLUE PRESSURE

CHECK MSC 3 BOARD

NEW TYPE CHECK接头 J928

POWER +12V POWER SUPPLY

SOLENOID VALVE---J1: PROBE RINSE

J2: WATER PRESSURE (BLUE TUBE)

J3: PROBE RINSE/ WATER (SYRINGE)

CHECK PROBE RINSE限制器 (二个) & FILTER

CHECK MSC 3 BOARD

76. REAGENT PROBE 漏水 CHECK BUBBLE GENERATOR

REAGENT PROBE 位置偏 ALIGNMENT REAGENT PROBE

CHECK 25 PSI

CHECK WASH CUP INSERT 5A VALVE, MSC 4 BOARD

SYRINGE & 3 WAY VALVE

77. SAMPLE PROBE 滴水或悬水珠 SAMPLE PROBE定位问题

CHECK 25 PSI

WASH CUP INSERT 4A VALVE, MSC 4 BOARD

78. WASH CUP 有水气喷出 CHECK HYDRONMENTIC SYSTEM---

WASH CUP 排气 FILTER 有无下垂或阻塞

79. SAMPLE NOT DETECTED 周期性 CHECK PROBE CABLE

LEVEL SENSOR BOARD

干扰 GROUNDING

SAMPLE CAROUSEL ALIGNMENT

SAMPLE PROBE ALIGNMENT

80. REAGENT NOT DETECTED AT SAMPLE 周期性发生 CHECK SAMPLE PROBE CABLE

INJECTION REAGENT STATUS

REAGENT PROBE

BUBBLE GENERATOR

REAGENT PUMP---SYRINGE, 3 WAY

VALVE

看 EVENT LOG---

那个 CUVETTE发生 CHECK CUVETTE

那个 CHEMISTRY REAGENT有气泡

REAGENT CARTRIDG破

CUVETTE 位置错误 ALIGNMENT REACTION CAROUSEL

NOISE 干扰 GROUNDING问题

81. PELTIER FAILURE CHECK 6个HEATSINK 电压 REPLACE HEATSINK

CHECK POWER SUPPLY 1

CHECK PELTIER CONTROL BOARD

CHECK STATUS BOARD

82. PELTIER TEMPERATURE HI CHECK 室温，CLEAN AIR FILTER 工作温度为18度至28度

CHECK PELTER REPLACE HEATSINK

CHECK REAGENT CAROUSEL 内温度 REPLACE THEMISTOR

CHECK POWER SUPPLY 1

CHECK PELTIER CONTROL BOARD

STATUS BOARD

83. POWER SUPPLY FAILURE (CX3* /CX3 )

CHECK INDICATOR BOARD (ONLY CX3* )

REPLACE

BOX 1 (POWER INPUT )---SUPPLY BOX 2~5, +17V HEATERS POWER SUPPLY

BOX 2 (+5V, -5v, +12V, -12V)---LOGIC, DISK DRIVER

BOX 3 (LAMP POWER SUPPLY )---CA / CREA LAMP

BOX 4 (+15V, -15V, +5V, +24V)---ANALOG, SOLENOID VALVE, MOTOR

BOX 5 (+13V )---STEP MOTOR

84. POWER SUPPLY FAILURE ( ISE ) PSI & 24V FREQUENCY BOARD 同时坏---CHECK INDICATOR BOARD

BREAKER

PSI

24V FREQUENCY BOARD REPLACE UPDATE KIT

CHECK STATUS/ SENSE BOARD & C32

PSI POWER SUPPLY: +5V, -5V, +15V, -15V, +13V

24V FREQUENCY BOARD: 24VAC

85. DBM FATAL ERROR # 0 SHUTDOWN INSTRUNMENT 二次 ( POWER DOWN )

REBOOT

DBM FATAL ERROR # 8 DELETE DATABASE

REBOOT INSTRUNMENT

DBM FATAL ERROR # ? ?

86.ANALOG CONTROL SENSOR ERROR CHECK PROX SENSOR RUN REACTION EXTENDED TEST

CHECK REACTION CAROUSEL ALIGNMENT CAROUSEL

CHECK EVENT LOG

MAC DETECTED: TYPE#5, 23 VERIFY HOME / SERVICE SENSOR

( HOME STACK ) CHECK CABLE BETWEEN HOME SENSOR AND MAC BOARD

MAC BOARD

MAC DETECTED: TYPE#6 VERIFY HOME SENSOR

( HOME TIME-OUT) CHECK MARGINAL REACTION CAROUSEL MOTOR VOLTAGE

MAC 3 BOARD, MMC BOARD

MAC DETECTED: TYPE#7 CHECK SYNC SENSOR

( SYNC STACK ) CABLE BETWEEN SYNC SENSOR AND MAC BOARD

MAC BOARD

MAC DETECTED: TYPE#20 CHECK SYNC SENSOR

(NO FLASH SYNC) REACTION WHEEL MOTOR

MAC BOARD

MAC DETECTED: TYPE#21 CHECK HOME / SERVICE SENSOR

(MISSED CUVETTE ) MSC / MMC /MAC BOARD

MAC DETECTED: TYPE#22 CHECK SYNC SENSOR

SENSOR ALIGNMENT

87.ANALOG COMMUNICATION ERROR CHECK EVENT LOG---

FLASH POWER FILE NOT FOUND REBOOT AFTER RESTORE BACKUP DISKETTE

RUN ANALOG SYSTEM ALIGNMENT

CHECK DISK OPERATION SYSTEM

FLASH DELAY FILE NOT FOUND 如上

ERROR SENDING FLASH DATA CHECK MAC BOARD, DISK OPERATION SYSTEM

REBOOT

RESULTS BLOCK CHECKSUM ERROR CHECK MULTI-BUS BACK PLANE

REBOOT

RESULTS MSG ADDRESS ERROR REBOOT

RESULTS OUT OF SEQUENCE REBOOT

RECEIVED RESULTS BEFORE READY REBOOT

ERROR SENDING CHEM. DATA REBOOT, CHECK MAC BOARD

ERROR STOPPING MAC 如上

ERROR STARTING MAC 如上

ERROR SENDING WORKLIST REBOOT

WORKLIST QUEUE IS EMPTY REBOOT

CAN NOT START PROCESS REBOOT

88.ANALOG COMMUNICATION ERROR CHECK EVENT LOG---

CAN NOT CREATE SEMAPHORE REBOOT

CAN NOT DOWNLOAD CODE REBOOT

MAC IS DEAD CHECK MAC BOARD, REBOOT

89.FATAL MMC ERROR:

MMC DETECTED NO COMM. FROM HOST

TOO MANY SUB SEQUENCES

BAD TERNINATE FUNC

TIMEOUT COURTING MSC

TIMEOUT READING MSC BAD PORT

BAD DIAG SEQUENCE FUNC

BAD SEQUENCE FUNC

BAD DEVICE

--- REBOOT REPLACE MMC BOARD

90.CHECKSUM ERROR POWER DOWN, REBOOT CHECK CPU / RAM BOARD

STACK OVERFLOW POWER DOWN, REBOOT CHECK CPU / RAM BOARD

HARDWARE MENORY PARITY ERROR CHECK CPU / RAM BOARD

POWER DOWN, REBOOT

SOFTWARE ERROR DETECTED CHECK DISKETTE ( CX3 )

DISK CONTROL BOARD

HARD DISK ( CX4/5 )

SCSI BOSRD, HP PC

OPERATING SYSTEM ERROR 如上

UNDEFINED APPLICATION ERROR 如上

91.MMC TIMOUT ERROR REBOOT

CHECK MMC BOARD

92.UNRECOGNIZED COMMAND SENT TO MMC REBOOT

REPLACE OPERATOR DISKETTE ( CX3 )

UNRECOGNIZED COMMAND RECEIVED TO MMC CHECK MMC BOARD

CPU BOARD

PARAMSTER SENT TO MMC OUT OF RANGE DISK DRIVER BOARD

93. MOTOMETER SYSTEM NOT READY CHECK MAC BOARD

INTERFACE BOARD

94. ANALOG WAS DEAD AT INITIALIZATION CR23 CR24 亮起 ---REPLACE MSC BOARD

CHECK POWER SUPPLY 3

MMC BOARD

95.FATAL NOTE- IOM MODULE: IDLE

IOM: Input/Output Module NOT RECOGNIZED MESSAGE RECEIVED

BAD IOM MESSAGE

BAD PRINT TASK CREATE

IOM TASK IS NOT RUNNING ( BAD SENT )

PRINT TASK IS NOT RUNNING ( BAD SENT )

NAME ATTACH FOR IOM FAILED

CAN’T OPEN PRINT TASK FILE (BAD FOPEN )

UNABLE TO ALLOCATE BUFFER MEMORY

----- REBOOT INSTRUMENT AFTER INSTRUMENT IDLE

96. FATAL ERROR--- COULD NOT POST ALARM EVENT

ALARM REQUEST LIST FULL

COULD NOT OPEN ALARM REQUEST QUEUE

COULD NOT OPEN EVENT QUEUE

COULD NOT CREATE ALARM AQENT TASK

COULD NOT POST ALARM REQUEST

COULD NOT REPORT ALARM EVENT

ALARM NOT RUNNING

---- REBOOT, CHECK HP PC

97.SCSI PROBLEM CHECK SCSI BOARD (CX3 / CX4)—JUMPER

SCSI BOARD (HP PC)

CABLE

ISOLATER BOARD

98.CANNOT START HEATER CALIBRTION CODE CHECK HEATER CONTROL BOARD---CALIBRATION CODE

99. DOES NOT MATCH DATA ON DISK ENTER DIAGNOSTIC---EXTENDED (6 ) TEMPERATURE CONTROL SYSTEM改正或重输 CODE

RESET INSTRUMENT

REPLACE REART CONTROL BOARD

100. INCOMPATIBLE TEMPERATURE BOARDS (如上)

101. CANNOT START: FATAL ANALOG ERROR CHECK MAC BOARD

RESET INSTRUMENT

102. CANNOT START: CX4 ANALOG SYSTEM NOT READY REBOOT INSTRUMENT THROUGH SYSTEM IDLE

103. CANNOT START: DATABASE ERROR IDLE, REBOOT

DELETE DATABASE

REINSTALL, SOFTWARE

CHECK STATUS MONTTOR

104. ERROR SYNCHRONIZING ISE PROBE HOME

AND CX4 SAMPLE CAROUSEL INSTALL SOFTWARE VERSION 1.8/2.2

CHECK CX4 MOTOR CONTROL SYSTEM

谢谢

翻译过来就好了。

挺全的，不过有好多也只是大概，实际上会有很多误报，感谢老大。

同意楼上的看法。

谢谢

能翻译成中文就好了

是呀！要是有中英文对照就好了！

全面啊。

谢谢分享